How much salt for an 8,000 gallon pool

Starting with plain water, you'll pour roughly 214 lb of salt into an 8,000 gallon pool to hit 3,200 ppm (parts per million, the number a salt test shows). That works out to 6 bags at 40 lb each. Got some salt in the water already? Enter your reading and watch the bag count shrink.

Units Gallons, pounds Liters, kilograms

Pool volume in gallonsgal

Don't know the gallons? Measure the pool

Pool shapeRectangleOvalRoundKidney

A: lengthftB: widthftShallow end depthftDeep end depthft

The gallons above fill in as you measure.

Salt reading now ppmYour chlorinatorTarget to dose to ppm

Example For 8,000 gallons, from 0 to 3,200 ppm. Type yours to see your bags.

Buy 6 bags of

Add 214 lb in all: pour 5 bags now, then 14 lb from bag 6 after you retest.

Pump on. Pour it around the deep end, not into the skimmer.
Brush any salt off the floor until it's gone.
Run the pump 24 hours and test. Add the rest only if the reading is still short.

How this is worked out

Gallons = A × B × average depth × 7.5 for a rectangle, 6.7 for an oval and 5.9 for a round pool (diameter × diameter), the factors in Hayward's manual; 7.0 for a kidney (length × average width), from Inyo's sizing guide. Pounds of salt = (target ppm − your ppm) × gallons × 8.34 ÷ 1,000,000. A gallon of water weighs 8.34 pounds. Bags round up. In liters: kilograms = ppm difference × liters ÷ 1,000,000.

Salt for 8,000 gallons by current reading

Reading now	to 3,000 ppm	to 3,200 ppm	to 3,600 ppm
0 ppm	Buy 5 bagsadd 200 lb	Buy 6 bagsadd 214 lb	Buy 6 bagsadd 240 lb
1,000 ppm	Buy 4 bagsadd 133 lb	Buy 4 bagsadd 147 lb	Buy 5 bagsadd 173 lb
1,500 ppm	Buy 3 bagsadd 100 lb	Buy 3 bagsadd 113 lb	Buy 4 bagsadd 140 lb
2,000 ppm	Buy 2 bagsadd 67 lb	Buy 2 bagsadd 80 lb	Buy 3 bagsadd 107 lb
2,500 ppm	Buy 1 bagadd 33 lb	Buy 2 bagsadd 47 lb	Buy 2 bagsadd 73 lb
2,800 ppm	Buy 1 bagadd 13 lb	Buy 1 bagadd 27 lb	Buy 2 bagsadd 53 lb
3,000 ppm	Already there	Buy 1 bagadd 13 lb	Buy 1 bagadd 40 lb

Every bag is 40 lb and the count rounds up. Pour all but the final bag, let the pump run a day, then test before you open it.

Intex and TruClear aim for 3,000 ppm, Hayward for 3,200 ppm and Pentair for 3,600 ppm. The chart by chlorinator lists every manufacturer's number.

Good to know at 8,000 gallons

In a pool this size, every 100 ppm gap takes 6.7 lb to close. So when your test reads 400 ppm under target, that's 27 lb: buy 1 bag and add 27 lb of it.

CircuPool's advice is to buy a cell sized for 1.5 to 2 times the water you hold. For this pool that is 12,000 to 16,000 gallons, which fits the Jandy AquaPure 700 or the Hayward T-CELL-3 (W3T-CELL-3) or the Pentair IntelliChlor LT15.

Close to this volume in the Intex range: the 20 ft x 52 in Metal Frame at 8,638 gallons. Intex equipment works at 3,000 ppm, and the numbers are on salt for Intex pools.

Questions people bring to the counter

How much does a backwash or a rainy week cost me in salt?

Only the water you lose takes salt with it. If a top-up brings this pool from 2,800 back to 3,200 ppm, that's 27 lb: buy 1 bag and add 27 lb of it.

How can I tell if my pool has enough salt?

Test the water. Most chlorinators light a low-salt warning below their range. A strip or drop kit reads in ppm, and that number goes in the salt reading box.

Next size down or up: 5,000 gal or 10,000 gal. Every size is on the per 1,000 gallons chart.